If the top of your tool box is lower than the bed rails of your 2019 Ford F-150 the Swagman Pick-Up Truck-Bed-Mounted 2 Bike Carrier # S64702 would fit easily.
Worst case scenario the rack would fit behind the tool box like in the picture I attached. view full answer...
The Buyers Products Truck Bed Ladder Rack # 3371501680 can fit trucks with tool boxes but if the tool box goes over the tops of the bed rails the front upright would have to install behind the box. If it's a chest style though it should fit around the box without issue. view full answer...
If the tool box was a chest style that didn't go over the tops of the bed rails the Yakima Overhaul HD Adjustable Truck Bed Rack # Y01151 would easily install without issue. Due to how this wraps around the bed rails (see picture) it couldn't fit with a crossover style box. view full answer...
Yes the Rightline Truck Bed Tent part # RL110730 that you referenced does fit the truck bed setup you have on your 2016 GMC Sierra short bed. It would fit over the bed rails and the rail system of your cover and tool box would not be an issue at all. view full answer...
Adding the 1 inch measurement will apply to the outside dimensions of the Truck Bed Chest, # DZ8546B. But since the lid overlaps the box, that 1 inch measurement will not be added to the bottom of the box, just where the lid is.
It will add some height to the top of the box with the lid factored in. I would say that the 1 inch measurement is the maximum which would make it 17 inches tall. view full answer...
I spoke with my contact at DeeZee about your 2002 Ford Ranger with the flareside. Although we do not offer a crossover tool box that would fit we do have an alternative for you.
I recommend the DeeZee Red Label Truck Bed Toolbox, part # DZ8537. This Brite-Tread aluminum tool box with a silver finish measures 37-1/8 inches long x 19 inches wide x 15-9/10 inches tall, and mounts to the floor of your pickup. If you choose not to mount the tool box to the bed of the truck, it has handles... view full answer...
I have a great tool box option for your 2022 Ford F-250 that sits below the rails of your truck bed. The UWS Truck Bed Chest # UWS01048 is going to do a great job of wisely using the space in your truck bed while staying below the bed rails. It is made in the USA and has a limited lifetime warranty. I have included a picture that shows how the box looks relative to the bed rails. view full answer...
If your tool box does not go over the tops of the bed rails like the "crossover" style boxes do and instead only mounts between the rails the Adarac ladder rack part # A70450 would fit and work well with it.
This rack installs on top of the bed rails and does not wrap around them in any way so chest style boxes that do not go above the rails will fit and work well. view full answer...
We don't have any confirmed fit for tool boxes for you 1986 GMC Caballero, but if you measure the dimensions of your truck bed you could determine if the part # DZM207 that you referenced would fit. This box is 35" long x 12" wide x 12-1/2" tall, if your truck bed can accommodate a box that big this one should work well for you.
Other smaller boxes include the following:
DeeZee Silver Toolbox, part # DZ74, measures 30 inches long x 20 inches wide x 18 inches tall. view full answer...
Yes we do offer low-profile crossover style truck bed tool boxes that are a confirmed fit for your 2017 Nissan Frontier 5 ft bed crew cab. We have the black UWS box part # UWS00377 and the silver version # UWS00367 that have capacity of 7.5 cubic feet. view full answer...
For your 2016 Chevy Silverado 3500 long bed with a tool box we have one solution that will work great but it's not from TruXedo. The only tonneau cover we have that fits your truck and is designed to fit behind a toolbox is the Access Toolbox Edition part # A62339. This is a very similar style of roll up tonneau that will work great and still give you ability to keep your tool box installed in your truck bed. view full answer...
The closest low-profile, DeeZee tool box to the # DZ6170N that you referenced is the DeeZee Red Label Low-Profile # DZ8170L.
The # DZ6170N has outside top dimensions of 69-3/4L x 12W x 14-1/4T inches and sits 5 inches above the truck rails on your 2013 Dodge Ram Pickup. The same outside top DeeZee # DZ8170L dimensions are 69-3/4L x 20W x 12-1/5T inches and sits 2 inches above the truck rails.
The important base dimension is the same for both boxes being 60-3/4 inches long.
The low... view full answer...
To do a retractable tonneau cover for your 2016 RAM 3500 and use a tool box will require you do go with a box that will fit underneath the tonneau.
The RetraxPRO part # RT80233 would be the cover that would work best for you as it is a fit for your truck and will retract far enough to fit a chest tool box. This has a matte black finish.
The DeeZee Red Label Truck Bed Toolbox # DZ8537 would then fit under the cover and would work well. I attached an install video for you to check out.
This... view full answer...
For your 2016 Ram 3500, I recommend the Extang Trifecta 2.0 Toolbox Edition # EX93435. This cover is designed to match up to most 18" to 20" standard toolboxes. This soft tonneau requires no assembly and no drilling. It is an easy install by simply setting cover on truck and tightening clamps. This can be used with a tool box like the DeeZee Red Label Truck Bed Toolbox - Deep, Crossover Style - Aluminum - 12 Cu Ft - Silver # DZ8170D if you don't already have a tool box. view full answer...
I have a solution for you but the Weather Guard Truck Tool Box # WG46ZV that you referenced is not a low profile box. It sits on top of the truck bed rails so it would not allow a tonneau cover to fit over it. It's also a wider box at 27-1/2 inches so a tonneau cover would not fit behind it either.
For a low profile toolbox that fits your 2020 Ford F-350 long bed that can fit with a tonneau cover the UWS tool box part # UWS07647 would be a really great option. Then for a tonneau cover... view full answer...
For your 2022 Ford F-250 we have the UWS tool box part # UWS01048 for a black box or the part # UWS01040 for bright aluminum that are a confirmed fit and are shorter than the bed rail height of your truck so your tonneau would be able to close over it. view full answer...
The tool box in your truck bed will interfere with your ladder rack. We have had customers work around this by putting their tool box in between the ladder rack uprights. With this setup you will have a ladder rack at the bulkhead in your truck and the toolbox just behind it.
The Thule TracRac TracONE Truck Bed Ladder Rack - Fixed Mount - 800 lbs - Silver, part # TH27000XT, will work with your 2011 Ford F-150. You will be able to move your tool box and mount it behind your forward most... view full answer...
The Taylor Made Marine Gas Strut for Boat Hatches part # 3691824-10 is as close as I can get you. It offers an overall extended length of 12" and compressed is closer to 8.5". Using dual struts on a Husky tool box the 10 lb. pressure shocks are going to be ideal. view full answer...
If the tool box was a chest style that fit between the bed rails of the truck and did not go over the top of the bed rails like a crossover box yes, the Adarac Ladder Rack part # A70450 would fit and work well.
If you had a crossover style where the top portion of the box did rest on top of the bed rails you'd need a different style that clamps around the bed rails like the Erickson part # EM07705 which you'd be able to mount behind the box. I attached a review video for this ladder rack... view full answer...
The Replacement Compression Latch for RC Manufacturing Underbody Truck or Trailer Tool Box part # 313-8-325-281 would appear to be the best replacement option for your tool box handle based on the photos. The handle measures 5-1/2" wide and 6" tall which you can see in the attached photo. It's expected that there may be some slight modifications required for fitment but this is pretty much going to be unavoidable as there isn't any sort of record for this to obtain an exact replacement. view full answer...
Go To Results